
Along the coast and through the interior — Tema, Accra, Takoradi, Kumasi — humidity is a permanent operating condition, not a season. For polythene producers it shows up as film that comes off the winder milky, hazy, or streaked with wavy marks, and buyers reject it on sight for clear-view packaging: sachet water film, bread bags, printed retail wraps.
Two different faults produce that appearance, and they need different fixes. Mixing them up is how plants spend weeks chasing the wrong one.
Moisture shows as silvery streaks running along the web, a milky cast, and micro-voids that open up at the seal. It comes from damp resin: washed sachet scrap and post-consumer pellet absorb humidity in the rainy season or in sacks sitting on a damp floor, and the water flashes to steam inside the barrel.
Slow cooling produces a different look — an even, dull haze with no voids and no seal failures. When the frost line floats high because the ambient air is warm or the blower is weak, the polymer has time to form large crystals, and large crystals scatter light instead of transmitting it.
The test is simple: check whether the haze is even or streaky, and whether seals fail. Streaks with voids mean water. An even dull cast that improves when you pull the frost line down means cooling.
A third, easily missed source belongs with cooling: condensation. Bare cold air hoses and chiller pipes sweat in coastal humidity, and the droplets get drawn into the blower stream and sprayed onto the molten bubble as wavy water marks.
Raising rear feed-zone temperatures to drive water out does not work. It softens recycled pellet before it reaches the screw, causes slip at the feed throat, and leaves the steam inside the melt anyway. Water leaves a melt through a vent, not through heat.
The correct fix is a dryer — hot-air or desiccant — sized for the throughput you actually run. Some plants avoid one because pellets bridge in a hopper that is simply heated rather than dried; that is an argument against a bad installation, not against drying.
Where a dryer is not yet in place, control what you can. Keep regrind sacks sealed and stacked on pallets away from open doors, especially overnight. In the wettest weeks, a calcium-oxide desiccant masterbatch at the supplier’s stated dose will bind some residual moisture, but it is a stopgap: it generates heat as it absorbs, and over-dosing leaves surface defects of its own.
A finer multi-layer screen at the breaker plate — 80/100/120 mesh — improves melt quality and removes the contamination that turns into voids, but it will not send vapour back to the hopper. Vented or vacuum-vented extrusion is what actually removes volatiles.
Changing that screen pack is hot work. Stop the line, vent the melt pressure, let the pack cool, and wear heat-resistant gloves and a face shield.
For clarity, cooling speed is the lever. Clean the blower intake filters — with the fan isolated — confirm the chiller water is genuinely cold, and raise air ring output until the frost line sits close to the die. Fast quenching locks the resin into fine, uniform crystals and the gloss comes back.
Keep the air ring level and do not let it blast cold air onto the steel lip; chilling one side of the melt while the other stays warm produces its own streak.
Insulate every cold line that runs to the ring. Closed-cell foam on the hoses and chiller pipes stops the sweating, and stops the droplets that were creating the water marks in the first place.
On a single-layer line running high local regrind, holding clarity through the rainy season is hard, because trace moisture and filler in the core both dull the surface and create voids.
An ABA or three-layer structure helps in a specific way: dry virgin LDPE or LLDPE in the skins gives a glossy, defect-free outer surface for print and sealing, while regrind sits in the core. It does not make core haze invisible — in a thin sachet film, voids in the middle layer are still visible and still weaken the seal. Co-extrusion reduces the problem and shifts it inward; the dryer and the filtration still do the real work.
On the equipment side, what matters in this climate is a dual-lip air ring that can hold a consistent frost line, insulated cooling ducts, and stable heater control so barrel temperatures do not drift when the grid does.
Dry resin, fine screens, a low and level frost line, insulated ducts, and honest expectations from co-extrusion. That is what keeps clear film clear in Ghana.
If moisture streaks or rainy-season clarity rejects are cutting into your yield, our technical team can review your resin handling and drying setup, and recommend the changes that fit your floor.

How to Fix Die Lines

How to Stop Bubble R

How to Produce High-

How to Fix Film Bloc